Husqvarna F2203P4 Repair Manual Download Page 242

Page: 242 / 381

18 ENGINE

18.5.20 Installing the piston

302642-10

303078-10

240

- Mount the starter idler gear with the washer.

- Mount lock ring

- Position the rotor.

•

Info

Ensure that the woodruff key is seated properly.

- Mount and tighten screw (D.

Guideline

Rotor screw

M10x1

70 Nm (51.6 lbf ft)

- Shift the joint of the piston rings by 120

Thread, oiled with

engine oil/cone

degreased

- Place the special tool on the oiled piston. Compress the pis-

ton rings using the special tool.
I Piston ring mounting tool (60029015000) (

�

p. 361)

✓ The piston rings are pushed together all the way.

- Position the piston on the cylinder using the special tool.

- Push the piston carefully into the cylinder from above.

Info

The piston rings should not catch or they will be dam

aged.

Summary of Contents for F2203P4






























































































































































































































































































































































































Search results

Summary of Contents for F2203P4

Reviews:

Related manuals for F2203P4

Brands by name

Popular brands

Husqvarna F2203P4, Repair Manual

Search results

Summary of Contents for F2203P4

Reviews:

Related manuals for F2203P4

Brands by name

Popular brands