manualshive.com logo in svg

Husqvarna F2203P4, Repair Manual

Share
Download
Husqvarna F2203P4 Repair Manual Download Page 107

305314-10 

12  FUEL TANK,  SEAT, TRIM 

Guideline 

Fuel connection on 

fuel pump 

M8 

- Mount and tighten screws 

C,.

Guideline

I 

Screw,  fuel pump 

I  EJOT PT

® 

Finishing work 

- Install the fuel tank. (

� 

p. 100)

- Mount the seat. (

� 

p. 97)

10 Nm (7.4 lbf ft) 

1 

2.3  Nm (1.7 lbf ft)

12.11 

Changing the fuel �um� 

A 

Danger 

Fire hazard 

Fuel is highly flammable.

The fuel in the fuel tank expands when warm and can escape if overfilled. 
- Do not refuel the vehicle in the vicinity of open flames or lit cigarettes.
- Switch off the engine for refueling.

- Make sure that no fuel is spilled; particularly not on hot parts of the vehicle.
- If any fuel is spilled, wipe it off immediately.

- Observe the specifications for refueling.

Warning 

Danger of poisoning 

Fuel is poisonous and a health hazard.

- Avoid skin, eye and clothing contact with fuel.
- Immediately consult a doctor if you swallow fuel.
- Do not inhale fuel vapors.

- In case of skin contact, rinse the affected area with plenty of water.

- Rinse the eyes thoroughly with water, and consult a doctor in case of fuel contact with the eyes.

- Change your clothing in case of fuel spills on them.

- Keep fuels correctly in a suitable canister, and out of the reach of children.

Warning 

Environmental hazard 

Improper handling of fuel is a danger to the environment.

- Do not allow fuel to enter the groundwater, the soil, or the sewage system.

Preparatory work 

- Drain the fuel from the fuel tank into a suitable container.
- Remove the seat. (

� 

p. 97)

- Remove the fuel tank. (

� 

p. 98)

105 

Summary of Contents for F2203P4






























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands