Husqvarna F2203P4 Repair Manual Download Page 151

Page: 151 / 381

16 BRAKE SYSTEM

Warning

Danger of accidents

Brake linings which have not been approved alter the braking efficiency.

Not all brake linings are tested and approved for Husqvarna motorcycles. The structure and friction

coefficient of the brake linings, and thus their brake power, may vary greatly from that of original brake
linings.

If brake linings are used that differ from the original equipment, compliance with the original homolo

gation is not guaranteed. In this case, the vehicle no longer corresponds to its condition at delivery
and the warranty shall be void.

Only use brake linings approved and recommended by Husqvarna motorcycles.

Warning

Environmental hazard

Hazardous substances cause environmental damage.

Dispose of oils, grease, filters, fuel, cleaning agents, brake fluid, etc., correctly and in compliance

with the applicable regulations.

Info

Never use DOT 5 brake fluid. It is silicone-based and purple in color. Oil seals and brake lines are not

designed for DOT 5 brake fluid.

Avoid contact between brake fluid and painted parts. Brake fluid attacks paint!

Use only clean brake fluid from a sealed container.

(FE EU/ AU, FE 350 US)

Move the brake fluid reservoir mounted on the handlebar

to a horizontal position.

Remove screws

Remove cover

with membrane @).

(FE 350 SUS)

Move the brake fluid reservoir mounted on the handlebar

to a horizontal position.

Remove screws

Remove cover

with membrane@).

Manually press the brake caliper to the brake disc to push

back the brake pistons. Ensure that brake fluid does not flow
out of the brake fluid reservoir, extracting it by suction if it
does.

Info

Make sure when pushing back the brake pistons that

you do not press the brake caliper against the spokes.

Remove cotter pins

pull out pin (3, and remove the

brake linings.
Clean the brake caliper and brake caliper support.

149

Summary of Contents for F2203P4






























































































































































































































































































































































































Search results

Summary of Contents for F2203P4

Reviews:

Related manuals for F2203P4

Brands by name

Popular brands

Husqvarna F2203P4, Repair Manual

Search results

Summary of Contents for F2203P4

Reviews:

Related manuals for F2203P4

Brands by name

Popular brands