Husqvarna F2203P4 Repair Manual Download Page 40

Page: 40 / 381

6 FORK, TRIPLE CLAMP

6.24

Installing the lower tri�le clam�

801632-10

402556-11

Main work

- Clean the bearing and sealing elements, check for damage,

and grease.

I High viscosity grease (

I!!:!

p. 354)

- Position the lower triple clamp with the steering stem. Mount

the upper steering head bearing.

- Check whether upper steering head seal

is correctly posi

tioned.

Mount protective ring

and 0-ring

- Position the upper triple clamp with the handlebar.

- Mount screw

but do not tighten yet.

- Position the clutch line in the guide above the voltage regula-

tor.

- Position the fork legs.

✓ Bleeder screws

are positioned toward the front.

Info

The compression damping is located in left fork

leg

COMP

(white adjusting screw). The rebound

damping is located in right fork leg

REB

(red adjusting

screw).

Grooves are milled into the side of the upper end of

the fork legs. The second milled groove (from the top)

must be flush with the upper edge of the upper triple

clamp.

Summary of Contents for F2203P4






























































































































































































































































































































































































Search results

Summary of Contents for F2203P4

Reviews:

Related manuals for F2203P4

Brands by name

Popular brands

Husqvarna F2203P4, Repair Manual

Search results

Summary of Contents for F2203P4

Reviews:

Related manuals for F2203P4

Brands by name

Popular brands