Husqvarna F2203P4 Repair Manual Download Page 32

Page: 32 / 381

6 FORK, TRIPLE CLAMP

804094-10

Assemblin the cartrid e

Info

- Grind the piston on both sides on a surfacing plate using

1200 grit sandpaper.

- Clean the piston.

- Lubricate the piston ring.

I Fork oil (SAE 4) (48601166S1) (

11\:!

p. 352)

- Mount the piston with chamfer

facing down.

- Mount rebound shim stack

with the smaller shims facing

upward.

Info

Note the setting list.

- Press the piston downward against the spring.

Info

Make sure the pistons do not squeeze the shims.

- Position valve @ in hydrostop needle

fD.

Mount and tighten

the hydrostop needle.
Guideline

Hydrostop needle on M6x0.5

piston rod

• Info

8 Nm (5.9 lbf ft)

silver hydrostop needle on compression damp

ing side.

G) - red hydrostop needle on rebound damping side.

- Unclamp the piston rod.

The operations are the same on both fork legs.

Preparatory work

- Assemble the seal ring retainer. (

11\:!

p. 28)

- Assemble the piston rod. (

11\:!

p. 29)

Summary of Contents for F2203P4






























































































































































































































































































































































































Search results

Summary of Contents for F2203P4

Reviews:

Related manuals for F2203P4

Brands by name

Popular brands

Husqvarna F2203P4, Repair Manual

Search results

Summary of Contents for F2203P4

Reviews:

Related manuals for F2203P4

Brands by name

Popular brands