Husqvarna F2203P4 Repair Manual Download Page 162

Page: 162 / 381

16 BRAKE SYSTEM

160

- Add brake fluid to level f).

I Brake fluid DOT 4 (

I!\',!

p. 352)

- Mount screw cap

with membrane

and O-ring.

Info

Clean up overflowed or spilled brake fluid immediately

with water.

Checking the free travel of foot brake lever

Warning

Danger of accidents

The brake system fails in the event of overheating.

If there is no free travel on the foot brake lever, pressure builds up in the brake system on the rear

brake.
- Set the free travel on the foot brake lever in accordance with the specification.

402026-10

- Disconnect spring

- Move the foot brake lever back and forth between the end

stop and the contact to the foot brake cylinder piston and

check free travel f).
Guideline

Free travel at foot brake

lever

3 ... 5 mm (0.12 ... 0.2 in)

If the free travel does not meet specifications:

- Adjust the basic position of the foot brake lever.

(

I!\',!

p. 161)

- Reconnect spring

Summary of Contents for F2203P4






























































































































































































































































































































































































Search results

Summary of Contents for F2203P4

Reviews:

Brands by name

Popular brands

Husqvarna F2203P4, Repair Manual

Search results

Summary of Contents for F2203P4

Reviews:

Brands by name

Popular brands