manualshive.com logo in svg

Husqvarna F2203P4, Repair Manual

Share
Download
Husqvarna F2203P4 Repair Manual Download Page 29

B03581-10 

B03584-10 

6  FORK, TRIPLE CLAMP 

Check the inner tube and axle clamp for damage. 

If there is damage: 

-

Change the inner tube.

Measure the outside diameter at multiple locations of the 

inner tube. 

Outside diameter of inner 
tube 

47.975  ... 48.005 mm 
(1 .88878 ... 1 .88996  in) 

If the measured value is smaller than the specified value: 

-

Change the inner tube.

Measure the run-out of the inner tube. 

I 

Inner tube run-out

I 

s  0.20 mm (s  0.0079 in)

If the measured value is larger than the specified value: 

-

Change the inner tube.

Measure the inside diameter at multiple locations of the outer 

tube. 

Inside diameter of outer 

tube 

s 49.20 mm (S  1 .937 in) 

If the measured value is larger than the specified value: 

-

Change the outer tube.

Check the outer tube for damage. 

If there is damage: 

-

Change the outer tube.

Check the surface of the sliding bushings. 

If the bronze-colored layer 

6) 

under sliding layer 

4D 

is

visible or the surface is rough: 
-

Change the sliding bushings.

27 

Summary of Contents for F2203P4






























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands