manualshive.com logo in svg

Husqvarna F2203P4, Repair Manual

Share
Download
Husqvarna F2203P4 Repair Manual Download Page 94

11  AIR  FILTER 

11.3 

Removin  the air filter 

Note 

-

Release catch 

O. 

pull 

off 

the air filter box lid sideways in 

areas  t) and 

4D, 

and remove  toward the rear. 

-

Position the air filter box cover and catch 

O. 

Engage the air

filter box cover in areas  t) and 

4D.

-

Engage catch 

O.

Engine damage 

Unfiltered intake air has a negative effect on the service life of the engine. 

Dust and dirt will enter the engine without an air filter. 

-

Never start to use the vehicle without an air filter.

92 

Warning 

Environmental  hazard 

Hazardous substances cause environmental damage. 

-

Dispose of oils, grease,  filters,  fuel,  cleaning agents,  brake fluid,  etc.,  correctly and in compliance

with the applicable regulations.

Preparatory work 

-

Remove the air filter box cover. (

a 

p. 92)

Main work 

-

Push air filter holding bracket 

O 

toward the air filter at posi­

tion  t),  and detach it at end 

4D.

Swivel the air filter holding bracket to one side and remove
the air filter with the air filter support.

- Take off air filter from air filter support.

Summary of Contents for F2203P4






























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands