Husqvarna F2203P4 Repair Manual Download Page 161

Page: 161 / 381

16 BRAKE SYSTEM

Stand the vehicle upright.

Remove screw cap

with membrane

and the 0-ring.

Press the brake caliper onto the brake disc by hand in order

to push back the brake piston and ensure that brake fluid
does not flow out of the brake fluid reservoir, extracting it by
suction if it does.

Info

Make sure when pushing back the brake piston that

you do not press the brake caliper against the spokes.

Remove cotter pins @), pull out pin

C,,

and remove the

brake linings.

Clean the brake caliper and brake caliper support.

Check that leaf spring

in the brake caliper and sliding

plate

in the brake caliper support are seated correctly.

✓ The arrow on the leaf spring points in the rotation direc

tion of the brake disc.

Insert the new brake linings, insert pin

C,,

and mount cotter

pins@).

•

Info

Always change the brake linings in pairs.

Make sure that decoupling plate @ is mounted on

the piston side brake lining.

Operate the foot brake lever repeatedly until the brake lin
ings are in contact with the brake disc and there is a pressure
point.

159

Summary of Contents for F2203P4






























































































































































































































































































































































































Search results

Summary of Contents for F2203P4

Reviews:

Related manuals for F2203P4

Brands by name

Popular brands

Husqvarna F2203P4, Repair Manual

Search results

Summary of Contents for F2203P4

Reviews:

Related manuals for F2203P4

Brands by name

Popular brands