manualshive.com logo in svg

Husqvarna F2203P4, Repair Manual

Share
Download
Husqvarna F2203P4 Repair Manual Download Page 154

16  BRAKE SYSTEM 

A 

152 

Adjusting free travel of hand  brake lever (FE EU/ AU,  FE 350 S US) 

H00198-10 

-

Check the free travel of the hand brake lever.  (

!lll 

p.  151)

- Adjust the free travel of the hand brake lever with adjusting

screw 

0-

Info 

Turn the adjusting  screw clockwise to reduce  free 

travel.  The pressure point moves away from the han­
dlebar. 

Turn the adjusting screw counterclockwise to increase 
free travel. The pressure point moves towards the 
handlebar. 
The range of adjustment is limited. 
Turn the adjusting screw by hand only,  and do not 
apply any force. 

Do not make any adjustments while riding! 

Checking the front brake fluid  level 

Warning 

Danger of accidents 

An insufficient brake fluid level will cause the brake system to fail. 

If the brake fluid level drops below the specified marking or the specified value,  the brake system is 

leaking or the brake linings are worn down. 

-

Check the brake system and do not continue riding until the problem is eliminated.

Warning 

Danger of accidents 

Old brake fluid reduces the braking effect. 

-

Make sure that brake fluid for the front and rear brake is changed in accordance with the service

schedule.

(FE  EU/AU,  FE  350 US) 

-

Move the brake fluid reservoir mounted on the handlebar

to a horizontal position.

-

Check the brake fluid level in level viewer 

O.

If the brake fluid has dropped below marking  6): 

- Add front brake fluid.  (

!lll 

p.  153)

(FE  350 SUS) 

-

Move the brake fluid reservoir mounted on the handlebar

to a horizontal position.

Check the brake fluid level in level viewer 

O.

If the brake fluid has dropped below marking  6): 

- Add front brake fluid.  (

a 

p.  153)

Summary of Contents for F2203P4






























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands