Husqvarna F2203P4 Repair Manual Download Page 110

Page: 110 / 381

12 FUEL TANK, SEAT, TRIM

Select the

"Function test of fuel pump control"

actuator

test.
Guideline

Maximum duration of the

actuator test

3 min

Check the fuel pressure with the filler cap closed.

Fuel pressure

When the fuel pump is
active

3.35 ... 3.65 bar (48.6 ...

52.9 psi)

If the specification is not reached:

Open the filler cap. (

p. 95)

Check the tank air vent system.

Check the fuel pressure with the filler cap open.

Fuel pressure

When the fuel pump is
active

3.35 ... 3.65 bar (48.6 ...

52.9 psi)

If the specification is not reached:

Check that the fuel line is clear.

Change the fuel filter. (

�

p. 103)

Change the fuel pump. (

�

p. 1 05)

Stop the

"Function test of fuel pump control"

actuator test

by pressing the

"Quit"

button.

Remove the special tools.

Join the fuel hose connection.

12.13 Removing the activated charcoal filter (FE 350 S US)

108

Preparatory work

Remove the seat. (

�

p. 97)

Remove the fuel tank. (

�

p. 98)

Main work

Detach rubber strap

Hang the activated charcoal filter to the side.

Summary of Contents for F2203P4






























































































































































































































































































































































































Search results

Summary of Contents for F2203P4

Reviews:

Related manuals for F2203P4

Brands by name

Popular brands

Husqvarna F2203P4, Repair Manual

Search results

Summary of Contents for F2203P4

Reviews:

Related manuals for F2203P4

Brands by name

Popular brands