manualshive.com logo in svg

Husqvarna F2203P4, Repair Manual

Share
Download
Husqvarna F2203P4 Repair Manual Download Page 288

27  CLEANING, CARE 

286 

- Treat bare metal (except for brake discs and the exhaust sys­

tem) with a corrosion inhibitor.

Preserving materials for paints,  metal and rubber 
(

�

p.  355)

- Treat all plastic parts and powder-coated parts with a mild

cleaning and care product.

(FE  EU/AU, FE  350 SUS) 

-

Grease steering lock.

I 

Universal oil spray (

!!,!l 

p.  355)

(FE  350 SUS) 

-

Grease the ignition switch.

I 

Universal oil spray (

!!,!l 

p.  355)

.. 

Checks and  maintenance ste�s for winter o  eration 

Info 

If 

you use the vehicle in winter, you must expect salt on the roads. You should therefore take precau­

tions against aggressive road salt. 

If 

the vehicle was operated in road salt,  clean it with cold water after riding. Warm water would enhance 

the corrosive effects of salt. 

401060-01 

-

Clean the motorcycle.  (

� 

p.  285)

-

Clean the brake system.

Info 

After 

EVERY 

trip on salted roads,  thoroughly wash the 

brake calipers and brake linings,  in the cooled down 
and installed state,  with cold water and dry carefully. 
After riding on salted roads,  thoroughly wash the vehi­
cle with cold water and dry it well. 

- Treat the engine, swingarm, and all other bright and zinc­

plated parts (except for the brake discs) with a wax-based
corrosion inhibitor.

Info 

Corrosion inhibitor is not permitted to come in contact 
with the brake discs as this would greatly reduce the 
braking force. 

-

Clean the chain.  (

!.l 

p.  133)

Summary of Contents for F2203P4






























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands