manualshive.com logo in svg

Husqvarna F2203P4, Repair Manual

Share
Download
Husqvarna F2203P4 Repair Manual Download Page 273

- Position the engine braces.

- Mount and tighten fittings (D.

Guideline

Screw, engine 

brace 

MB 

- Position the radiator on the right.

- Mount and tighten screws 

0.

- Mount right radiator shield 

8.

23  CYLINDER  HEAD 

33 Nm (24.3 lbf ft) 

Loctite

®

2701 

TM 

- Mount and tighten the spark plug with special tool (D.

Guideline

I

Spark plug 

I

M10x1 

110 ... 12 Nm (7.4 

_ 

_ 

_  ... 8.9 lbf ft)

I 

Spark plug wrench with link (77229172000) (

� 

p. 366)

- Plug in spark plug connector 

8.

- Plug in the connector and position cover 

0-

Finishing work 

(FE  EU/ AU,  FE  350 US) 

- Install the fuel tank. (

� 

p. 100)

- Mount the seat. (

� 

p. 97)

(FE  350 SUS) 

- Install the activated charcoal filter. (

� 

p. 109)

- Install the fuel tank. (

� 

p. 100)

- Mount the seat. (

� 

p. 97)

Ad"usting the valve clearance 

Info 

For purposes of illustration, the following operations are shown with the engine removed. 

Removal is not necessary. 

Preparatory work 

(FE  EU/AU,  FE  350 US) 

- Remove the seat. (

� 

p. 97)

- Remove the fuel tank. (

� 

p. 98)

(FE  350 SUS) 

- Remove the seat. (

a 

p. 97)

- Remove the fuel tank. (

a 

p. 98)

- Remove the activated charcoal filter. (

� 

p. 1 08)

- Check the valve clearance. (

l!!JI 

p. 268)

271 

Summary of Contents for F2203P4






























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands