Husqvarna F2203P4 Repair Manual Download Page 130

Page: 130 / 381

14 WHEELS

14.8.3

Changing the rear brake disc

Info

Position chain adjuster 6). Mount nut

C,,

but do not

tighten it yet.

Make sure that chain adjusters 6) are fitted correctly on

adjusting screws

Check the chain tension. (

!l;!l

p. 129)

Tighten nut

C,.

Guideline

M20x1 .5

Info

80 Nm (59 lbf ft)

The wide adjustment range of the chain adjusters

(32 mm (1.26 in)) enables different secondary

ratios with the same chain length.

Chain adjusters 6) can be turned by 180

Operate the foot brake lever repeatedly until the brake
linings are in contact with the brake disc and there is a
pressure point.

Finishing work

Remove the motorcycle from the lift stand. (

!!ll

p. 13)

If the brake discs are changed, the brake linings must also be changed.

128

Preparatory work

Raise the motorcycle with a lift stand. (

!l;!l

p. 13)

Remove the rear wheel. (

!l;!l

p. 125)

Main work

(FE EU/AU, FE 350 US)

Remove screws

Take off the brake disc.

Clean the contact surface of the brake disc.

Position the new brake disc with the label facing outward.

Mount and tighten screws

Guideline

Screw, rear
brake disc

(FE 350 SUS)

14 Nm (10.3 lbf ft)

Loctite

243

™

Remove screws

Take off the brake disc.

Clean the contact surface of the brake disc.

Position the new brake disc with the label facing outward.

Mount and tighten screws

Guideline

Screw, rear
brake disc

14 Nm (10.3 lbf ft)

Loctite

243

™

Summary of Contents for F2203P4






























































































































































































































































































































































































Search results

Summary of Contents for F2203P4

Reviews:

Related manuals for F2203P4

Brands by name

Popular brands

Husqvarna F2203P4, Repair Manual

Search results

Summary of Contents for F2203P4

Reviews:

Related manuals for F2203P4

Brands by name

Popular brands