Husqvarna F2203P4 Repair Manual Download Page 102

Page: 102 / 381

12 FUEL TANK, SEAT, TRIM

12.8

100

Installing the fuel tank

Danger

Fire hazard

Fuel is highly flammable.

The fuel in the fuel tank expands when warm and can escape if overfilled.
-

Do not refuel the vehicle in the vicinity of open flames or lit cigarettes.

Switch off the engine for refueling.

Make sure that no fuel is spilled; particularly not on hot parts of the vehicle.

If any fuel is spilled, wipe it off immediately.

Observe the specifications for refueling.

Warning

Danger of poisoning

Fuel is poisonous and a health hazard.

- Avoid skin, eye and clothing contact with fuel.
-

Immediately consult a doctor if you swallow fuel.

Do not inhale fuel vapors.

In case of skin contact, rinse the affected area with plenty of water.

Rinse the eyes thoroughly with water, and consult a doctor in case of fuel contact with the eyes.

Change your clothing in case of fuel spills on them.

-• •-

...

'.a.

�

H00188-11

Main work

Check the routing of the throttle cable. (

!!:!

p. 45)

Position the fuel tank and fit the two spoilers to the sides of

the radiator bracket.

Make sure that no cables or throttle cables are trapped or

damaged.

- Attach the hose to the fuel tank breather on the tank lid.
-

Mount and tighten screw

with the rubber bushing.

Guideline

Remaining screws,

chassis

(FE EU/AU)

10 Nm (7.4 lbf ft)

Position the collar bushings and horn, and mount and

tighten screws f!}.

Guideline

Remaining screws,

chassis

Connect the connector of the horn.

10 Nm (7.4 lbf ft)

Summary of Contents for F2203P4






























































































































































































































































































































































































Search results

Summary of Contents for F2203P4

Reviews:

Brands by name

Popular brands

Husqvarna F2203P4, Repair Manual

Search results

Summary of Contents for F2203P4

Reviews:

Brands by name

Popular brands