manualshive.com logo in svg

Husqvarna F2203P4, Repair Manual

Share
Download
Husqvarna F2203P4 Repair Manual Download Page 133

14  WHEELS 

Info 

The wide adjustment range of the chain adjusters 

(32 mm (1 .26 in)) enables different secondary 

ratios with the same chain length. 

Chain adjusters 

8 

can be turned by 180

°

. 

Finishing  work 

-

Remove the motorcycle from the lift stand. (

a 

p. 13)

14.8.6 

Checking the chain, rear sprocket, engine sprocket, and chain guide 

400227-01 

o

l 

o  o--�--0  o 

l 

o

2  3 

16  17  18 

400987-10 

Preparatory work 

-

Raise the motorcycle with a lift stand. (

I!!]] 

p. 13)

Main work 

-

Shift the transmission to idle.

-

Check the rear sprocket and engine sprocket for wear.

If the rear sprocket and engine sprocket are worn: 

-

Change the drivetrain kit. (

a 

p. 134)

•

Info

I 

The engine sprocket,  rear sprocket and chain 
should always be replaced together. 

-

Pull at the top part of the chain with the specified weight  f).

Guideline

Weight of chain wear mea­
surement 

10 ... 15 kg (22 ... 33 lb.) 

-

Measure distance  G)  of 18 chain rollers in the lower chain

section.

Info 

Chain wear is not always even,  so you should repeat 
this measurement at different chain positions. 

Maximum distance  G)  at 

the longest chain section 

272 mm (10. 71 in) 

If distance  G)  is greater than the specified measurement: 

-

Change the drivetrain kit. (

I!!]] 

p. 134)

Info 

When the chain is replaced,  the rear sprocket 
and engine sprocket should also be changed. 

New chains wear out faster on old,  worn 

sprockets. 

131 

Summary of Contents for F2203P4






























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands