manualshive.com logo in svg

Husqvarna F2203P4, Repair Manual

Share
Download
Husqvarna F2203P4 Repair Manual Download Page 136

14  WHEELS 

Info 

The service life of the chain depends largely on its maintenance. 

400725-01 

14.8.9 

Changing the drivetrain  kit 

134 

Preparatory work 

- Raise the motorcycle with a lift stand. (

!!:!J 

p.  13)

Main work 

- Rinse off loose dirt with a soft jet of water.

- Clean chain and apply chain spray.

I  Offroad chain spray (

!!:!J 

p. 354)

Finishing work 

- Remove the motorcycle from the lift stand. (

!!:!J 

p.  13)

Preparatory work 

- Raise the motorcycle with a lift stand. (

!!:!J 

p.  13)

Main work 

- Remove screws 

O 

and  @.

- Take off the engine sprocket cover.

- Have an assistant operate the rear brake.

- Remove screw 

@) 

with the washer.

- Remove the rear wheel. (

� 

p.  125)

- Remove connecting link 

8 

of the chain.

Info 

Cover the components to protect them against dam­

age. 

- Take off the chain.

Summary of Contents for F2203P4






























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands