Husqvarna F2203P4 Repair Manual Download Page 28

Page: 28 / 381

6 FORK, TRIPLE CLAMP

6.16

Remove adapter

C,.

Remove hub

Remove O-ring from the hub.

Remove shim stack C).

Remove washer @.

Remove O-ring

@).

Disassembling the seal ring retainer

Info

The steps are identical for both fork legs.

R00013-10

Checking the fork legs

Preparatory work

Disassemble the fork legs. (

!i.,!I

p. 20)

Remove the spring. (

!i.,!I

p. 22)

Disassemble the cartridge. (

!i.,!I

p. 23)

Main work

Remove pilot bushing support

Remove O-ring

and seal ring@.

Condition

The fork legs have been disassembled.

Summary of Contents for F2203P4






























































































































































































































































































































































































Search results

Summary of Contents for F2203P4

Reviews:

Related manuals for F2203P4

Brands by name

Popular brands

Husqvarna F2203P4, Repair Manual

Search results

Summary of Contents for F2203P4

Reviews:

Related manuals for F2203P4

Brands by name

Popular brands