Husqvarna F2203P4 Repair Manual Download Page 205

Page: 205 / 381

18.4.7

18 ENGINE

Installing the crankshaft bearing inner race

- Fix the crankshaft in the vise.

•

Info

Use soft jaws.

- Slide on the compensating disk.

- Heat the crankshaft bearing inner race in special tool

and

mount together.
Guideline

1120 oc (248 OF)

Puller (58429037037) (

!ill

p. 359)

- Repeat the operation on the opposite side.

- Ensure that the new crankshaft bearing inner race is flush.

Info

After replacing the crankshaft bearings, the crankshaft

end play must be measured.

18.4.8

Changing the connecting rod, conrod bearing and crank pin

Main work

- Position crankshaft

in the press using special tool

@}.

Separator plate (77229009000) (

!ill

p. 363)

- Press the crank pin with the special tool out of the upper

crank web.

Crankshaft pressing tool (75029047000) (

�

p. 362)

•

Info

Hold the lower crank web.

- Remove the connecting rod and bearing.
- Press the crank pin out of the lower crank web.

203

Summary of Contents for F2203P4






























































































































































































































































































































































































Search results

Summary of Contents for F2203P4

Reviews:

Brands by name

Popular brands

Husqvarna F2203P4, Repair Manual

Search results

Summary of Contents for F2203P4

Reviews:

Brands by name

Popular brands