manualshive.com logo in svg

Husqvarna F2203P4, Repair Manual

Share
Download
Husqvarna F2203P4 Repair Manual Download Page 54

9  SHOCK ABSORBER, SWINGARM 

9.7 

A 

52 

Checking the riding sag of the shock absorber 

- Measure distance 

G 

of rear wheel unloaded.(� p. 51)

- With another person holding the motorcycle, the rider, wear­

ing full protective clothing, sits on the seat in a normal sitting

position (feet on footrests) and bounces up and down a few

times.

✓ The rear wheel suspension levels out.

- Another person now measures the distance between the rear

axle and the fixed point.

- Note down the value as dimension (9.

Info 

The riding sag is the difference between measure­

ments 

G 

and  (9. 

- Check the riding sag.

I  Riding sag

1100 mm (3.94 in) 

If the riding sag differs from the specified measurement: 

- Adjust the riding sag. (

a 

p. 53)

Adjusting the s�ring  reload of the shock absorber 

Caution 

Risk of injury 

rectly. 

Parts of the shock absorber will fly off if the shock absorber is disassembled incor-

The shock absorber is filled with highly compressed nitrogen. 
- Please follow the description provided.

Info 

Before changing the spring preload, make a note of the present setting,  e.g., by measuring the length of 

the spring. 

Preparatory work 

- Raise the motorcycle with a lift stand. (

a 

p. 13)

- Remove the right side cover. (

a 

p. 96)

- Remove the main silencer. (

a 

p. 87)

- Remove the seat. (

a 

p. 97)

- Remove the manifold. (

a 

p. 83)

- Remove shock absorber. (

� 

p. 54)

- After removing the shock absorber, clean it thoroughly.

Summary of Contents for F2203P4






























































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands