Husqvarna F2203P4 Repair Manual Download Page 89

Page: 89 / 381

10 EXHAUST

Info

Raise the wheel slightly to be able to mount the screw

more easily.

(EU)

Connect plug-in connector

of the lambda sensor,

route the cable without tension, and secure with a new
cable tie.

Install the fuel tank. (

l!!ll

p. 100)

Finishing work

Install the main silencer. (

l!!ll

p. 87)

Install the right side cover. (

l!!ll

p. 96)

Mount the seat. (

!!,!I

p. 97)

Remove the motorcycle from the lift stand. (

!!,!I

p. 13)

Removin the main silencer

Warning

Danger of burns

The exhaust system gets very hot when the vehicle is driven.

- Allow the exhaust system to cool down before performing any work on the vehicle.

Preparatory work

Remove the right side cover. (

l!!ll

p. 96)

Main work

Disconnect spring

Spring hook (50305017000) (

p. 357)

Remove screws

and take off the main silencer.

Main work

Mount the main silencer. Mount screws

but do not

tighten yet.

- Attach spring

Spring hook (50305017000) (

p. 357)

- Tighten screws

Guideline

Remaining screws,

chassis

10 Nm (7.4 lbf ft)

Summary of Contents for F2203P4






























































































































































































































































































































































































Search results

Summary of Contents for F2203P4

Reviews:

Brands by name

Popular brands

Husqvarna F2203P4, Repair Manual

Search results

Summary of Contents for F2203P4

Reviews:

Brands by name

Popular brands