Husqvarna F2203P4 Repair Manual Download Page 266

Page: 266 / 381

21 LUBRICATION SYSTEM

264

Danger

Danger of poisoning

Exhaust gases are toxic and

inhaling them may result in unconsciousness and
death.
- Always make sure there is sufficient ventilation

when running the engine.

Use an effective exhaust extraction system when

starting or running the engine in an enclosed
space.

Start the engine and let it warm up.

Check the engine oil pressure.

Engine oil pressure

Engine oil temperature:

80 °C (176 °F)

Engine speed:

1,600 rpm

Engine oil temperature:

80 oc (176 °F)

Engine speed:

6,000 rpm

0.9 bar (13 psi)

2.5 bar (36 psi)

If the measured value is less than the specification:

Check the oil pumps for wear. Check that all oil holes
are clear.

Switch off the engine.

Warning

Danger of burns

Some vehicle components get

very hot when the machine is driven.
-

Wear appropriate protective clothing and safety
gloves. In case of burns, rinse immediately with
lukewarm water.

Remove the special tools.

Mount and tighten the release screw of the chain adjuster.
Guideline

Screw, unlocking

M10x1

8 Nm (5.9 lbf ft)

of timing chain ten-

sioner

Summary of Contents for F2203P4






























































































































































































































































































































































































Search results

Summary of Contents for F2203P4

Reviews:

Brands by name

Popular brands

Husqvarna F2203P4, Repair Manual

Search results

Summary of Contents for F2203P4

Reviews:

Brands by name

Popular brands