Husqvarna F2203P4 Repair Manual Download Page 157

Page: 157 / 381

D00461-10

D00462-10

-4!)

16 BRAKE SYSTEM

(FE EU/AU, FE 350 US)

- Move the brake fluid reservoir mounted on the handlebar

to a horizontal position.

- Cover painted parts.

- Remove screws

- Take off cover

with the membrane.

- Draw the old brake fluid out of the brake fluid reservoir

using a syringe and fill with fresh brake fluid.

Syringe (50329050000) (

�

p. 358)

Brake fluid DOT 4 (

!!.,!I

p. 352)

- Mount bleeder cover

@).

I Bleeder cover (00029013005) (

l!!ll

p. 356)

- Connect the bleeding device.

I Bleeding device (00029013100) (

�

p. 356)

- Open shut-off valve

C,.

Info

Follow the operating instructions of the bleeding

device.

- Ensure that the filling pressure is set on pressure

gauge f). Correct the filling pressure on pressure

regulator G) if necessary.

Guideline

I Filling pressure

I 2 ... 2.5 bar (29 ... 36 psi)

- Pull off protection cap

of the brake caliper bleeder

screw. Connect the bleeder bottle hose.
I Bleeding device (00029013100) (

�

p. 356)

- Open bleeder screw

by approx. one half turn.

•

Info

Drain until fresh brake fluid emerges in the bleeder

bottle hose without bubbles.

- Tighten the bleeder screw.

- Close shut-off valve

C,.

- Open the bleeder screw again until brake fluid stops

emerging.

•

Info

Overfilling of the brake fluid reservoir is prevented.

- Tighten the bleeder screw. Remove the bleeder bottle

hose. Attach the protection cap.

155

Summary of Contents for F2203P4






























































































































































































































































































































































































Search results

Summary of Contents for F2203P4

Reviews:

Related manuals for F2203P4

Brands by name

Popular brands

Husqvarna F2203P4, Repair Manual

Search results

Summary of Contents for F2203P4

Reviews:

Related manuals for F2203P4

Brands by name

Popular brands