Husqvarna F2203P4 Repair Manual Download Page 263

Page: 263 / 381

21 LUBRICATION SYSTEM

Position oil screen

with the O-rings on a pin wrench.

Position the pin wrench through the drilled hole of the screw

plug in the opposite section of the engine case.

Push the oil screen all the way into the engine case.

Mount and tighten screw plug

with the O-ring.

Guideline

Screw plug, oil
screen

M20x1 .5

15 Nm (11.1 lbf ft)

Mount and tighten the oil drain plug

with the magnet and

a new seal ring.

Guideline

Oil drain plug with
magnet

M12x1 .5

20 Nm (14.8 lbf ft)

Remove screws

C,.

Remove the oil filter cover with the O

ring.

Pull oil filter

out of the oil filter housing.

Lock ring plier (51012011000) (

p. 358)

Completely drain the engine oil.

- Thoroughly clean the parts and sealing area.

Lay the motorcycle on its side and fill the oil filter housing to

about½ full with engine oil.

Fill the oil filter with engine oil and place it in the oil filter

housing.

Lubricate the O-ring of the oil filter cover and mount it with

the oil filter cover (D.

Mount and tighten the screws.

Guideline

Screw, oil filter cover

Stand the motorcycle upright.

10 Nm (7.4 lbf ft)

261

Summary of Contents for F2203P4






























































































































































































































































































































































































Search results

Summary of Contents for F2203P4

Reviews:

Brands by name

Popular brands

Husqvarna F2203P4, Repair Manual

Search results

Summary of Contents for F2203P4

Reviews:

Brands by name

Popular brands