Husqvarna F2203P4 Repair Manual Download Page 66

Page: 66 / 381

9 SHOCK ABSORBER, SWINGARM

201404-10

9.19

Removin the heim joint

- Check the piston rings for damage and wear.

If damage or a bronze-colored surface is visible:

- Change the piston.

Condition

The shock absorber has been removed.

- Clamp the shock absorber in the vise using soft jaws for pro

tection.

Remove the collar bushing of the heim joint.

I Drift (T120) (

�

p. 367)

- Turn the shock absorber and remove the second collar bush

ing of the heim joint.

- Remove seal rings

on both sides.

- Press the heim joint against a lock ring using the special tool.

I Pressing tool (T1207S) (

ll!:!l

p. 368)

- Remove the second lock ring

- Place special tool

underneath and press out heim

joint

with special tool G).

I Pressing tool (T1207S) (

�

p. 368)

Summary of Contents for F2203P4






























































































































































































































































































































































































Search results

Summary of Contents for F2203P4

Reviews:

Brands by name

Popular brands

Husqvarna F2203P4, Repair Manual

Search results

Summary of Contents for F2203P4

Reviews:

Brands by name

Popular brands