Husqvarna F2203P4 Repair Manual Download Page 60

Page: 60 / 381

9 SHOCK ABSORBER, SWINGARM

201457-01

9.13

- Remove the spring. (

!!',!

p. 58)

- Disassemble the damper. (

!!',!

p. 59)

- Disassemble the piston rod. (

!!',!

p. 60)

- Disassemble the seal ring retainer.(!!',! p. 61)

- Check the damper. (

p. 63)

- Remove the heim joint. (

p. 64)

- Install the heim joint. (

p. 65)

- Assemble the seal ring retainer. (

p. 65)

- Assemble the piston rod. (

il,l

p. 66)

- Assemble the damper. (

il,l

p. 68)

- Install the spring. (

p. 74)

Condition

The shock absorber has been removed.

- Clamp the shock absorber in the vise using soft jaws for pro-

tection.

- Measure and note spring length in its preloaded state.

- Loosen screw

- Turn adjusting ring until the spring is no longer under tension.

I Hook wrench (T1 06S) (

il,l

p. 367)

- Remove ring

- Remove spring retainer@) and intermediate washer

C,.

- Remove the spring.

Summary of Contents for F2203P4






























































































































































































































































































































































































Search results

Summary of Contents for F2203P4

Reviews:

Brands by name

Popular brands

Husqvarna F2203P4, Repair Manual

Search results

Summary of Contents for F2203P4

Reviews:

Brands by name

Popular brands