Husqvarna F2203P4 Repair Manual Download Page 209

Page: 209 / 381

305004-10

18 ENGINE

Info

The cylinder size

is marked on the cylinder collar.

Using a straightedge and the special tool, check the sealing

area of the cylinder head for distortion.

Feeler gauge (59029041100) (

�

p. 360)

Cylinder/cylinder head - dis-

:;; 0.10 mm (:;; 0.0039 in)

tortion of sealing area

If the measured value does not meet specifications:

Change the cylinder.

18.4.15 Checking/measuring the piston

e-'

•

400995-10

305017-10

Use the special tool to measure clearance

of the piston

rings in the piston ring groove.

Guideline

Piston ring - groove clear

ance

:;; 0.08 mm(:;; 0.0031 in)

Feeler gauge (590290411 00) (

�

p. 360)

If play

is larger than the specified value:

Change the piston and piston rings.

Check/measure the cylinder. (

�

p. 206)

Check the piston sliding surface for damage.

If the piston sliding surface is damaged:

Replace the piston and, if necessary, the cylinder.

Check that the piston rings move easily in the piston ring

grooves.

If the piston ring is stiff:

Clean the piston ring groove.

Tip

An old piston ring can be used to clean the
piston ring groove.

Check the piston rings for damage.

If the piston ring is damaged:

Replace the piston ring.

•

Info

Mount the piston ring with the marking facing

upward.

Check the piston pins for discoloration or signs of wear.

If the piston pin shows severe discoloration/signs of wear:

Change the piston pin.

Place the piston pin in the connecting rod and check the

seating for play.

If the piston pin seating has excessive play:

Change the connecting rod and piston pin.

207

Summary of Contents for F2203P4






























































































































































































































































































































































































Search results

Summary of Contents for F2203P4

Reviews:

Brands by name

Popular brands

Husqvarna F2203P4, Repair Manual

Search results

Summary of Contents for F2203P4

Reviews:

Brands by name

Popular brands