Husqvarna F2203P4 Repair Manual Download Page 145

Page: 145 / 381

15.3

Checking the starter rela�

601201-10

Removing the batte�

Warning

15 WIRING HARNESS, BATTERY

Preparatory work

(FE EU/AU)

Press and hold the kill switch � while the engine is idling

until the engine stops.

(FE 350 US)

Press and hold the kill switch � while the engine is idling

until the engine stops.

(FE 350 SUS)

- While the engine is idling, turn the key in the ignition lock

to the position �-

Remove the seat. (

p. 97)

Main work

Disconnect the negative cable of the battery.

Pull the starter relay off of the bracket.

Pull off connector

Disconnect cables

and (Don the starter relay.

- Connect the starter relay to a 12 V power supply as per the

figure.

Measure the resistance between the specified points.

Resistance of open circuit

O Q

If the value displayed does not meet specifications:

- Change the starter relay.

Risk of injury

Battery acid and battery gases cause serious chemical burns.

Keep batteries out of the reach of children.

- Wear suitable protective clothing and safety glasses.
- Avoid contact with battery acid and battery gases.
-

Keep sparks or open flames away from the battery.

- Only charge batteries in well-ventilated rooms.
-

Rinse the affected area immediately with plenty of water in the event of contact with the skin.

Rinse eyes with water for at least 15 minutes and consult a doctor immediately if battery acid and

battery gases get into the eyes.

Preparatory work

(FE EU/AU)

Press and hold the kill switch � while the engine is idling

until the engine stops.

143

Summary of Contents for F2203P4






























































































































































































































































































































































































Search results

Summary of Contents for F2203P4

Reviews:

Related manuals for F2203P4

Brands by name

Popular brands

Husqvarna F2203P4, Repair Manual

Search results

Summary of Contents for F2203P4

Reviews:

Related manuals for F2203P4

Brands by name

Popular brands