Husqvarna F2203P4 Repair Manual Download Page 55

Page: 55 / 381

9.8

Adjusting the riding sag

9 SHOCK ABSORBER, SWINGARM

Main work

Loosen screw

- Turn adjusting ring

until the spring is no longer under ten-

sion.

Hook wrench (T1 06S) (

p. 367)

Measure the overall spring length while the spring is not

under tension.

- Tighten the spring by turning adjusting ring

to measure

ment

Guideline

Spring preload

•

Info

117 mm (0.67 in)

Depending on the static sag and/or the riding sag, it

may be necessary to increase or decrease the spring
preload.

- Tighten screw

Guideline

Screw, shock

absorber adjusting

ring

Finishing work

Install the shock absorber.(� p. 55)

Install the manifold. (

p. 85)

Mount the seat. (

p. 97)

Install the main silencer. (

p. 87)

Install the right side cover. (

p. 96)

5 Nm (3.7 lbf ft)

Remove the motorcycle from the lift stand. (

l!t!I

p. 13)

Preparatory work

Raise the motorcycle with a lift stand. (

p. 13)

Remove the right side cover. (

p. 96)

Remove the main silencer. (

p. 87)

Remove the seat. (

l!t!J

p. 97)

Remove the manifold. (

l!t!I

p. 83)

Remove shock absorber. (

�

p. 54)

- After removing the shock absorber, clean it thoroughly.

Summary of Contents for F2203P4






























































































































































































































































































































































































Search results

Summary of Contents for F2203P4

Reviews:

Related manuals for F2203P4

Brands by name

Popular brands

Husqvarna F2203P4, Repair Manual

Search results

Summary of Contents for F2203P4

Reviews:

Related manuals for F2203P4

Brands by name

Popular brands