manualshive.com logo in svg

HP 316095-B21 - StorageWorks Edge Switch 2/24, Service Manual

Share
Download
HP 316095-B21 - StorageWorks Edge Switch 2/24 Service Manual Download Page 68

2–48

edge switch 2/24 service manual

Diagnostics

10

Verify the hubs are correctly daisy-chained (

Figure 2–11

.)

Figure 2–11:  Ethernet Hubs, daisy-chained

To check two hubs, use 

step a

 and 

step b

 (top and middle hub instructions only).

a. At the first (top) Ethernet hub, ensure an RJ-45 Ethernet patch cable connects to 

port 24 and the medium-dependent interface (MDI) switch is set to MDIX (in).

b. At the middle Ethernet hub, ensure the patch cable from the top hub connects to 

port 12x, the patch cable from the bottom hub connects to port 23x, and the MDI 
switch is set to MDI (out).

c. At the bottom Ethernet hub, ensure the patch cable from the middle hub connects 

to port 24 and the MDI switch is set to MDIX (in).

Was a corrective action performed?

NO

YES

↓

Go to 

step 1

.

MDIX

MDI

MDIX

MDI

MDIX

MDI

Switch set to
MDI (out)

Switch set to
MDIX (in)

Switch set to
MDIX (in)

12x

24

12x

24

12x

24

Summary of Contents for 316095-B21 - StorageWorks Edge Switch 2/24



































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands