HP 316095-B21 - StorageWorks Edge Switch 2/24 Service Manual Download Page 61

Page: 61 / 322

edge switch 2/24 service manual

2–41

Diagnostics

Did the Product Manager application display a window with the message

Product

Manager error 5001

Product Manager error 5002

YES

↓

A Product Manager application error occurred. Click OK to close the window
and close the HAFM and Product Manager applications. Go to

step 3

Did the Product Manager application display a window with the message Send
firmware failed?

YES

↓

Go to

step 11

An attempt to download a firmware version from the HAFM server (or
customer-supplied server) hard drive to the switch failed. Retry the operation (

Manage

Firmware Versions on page 3–32

Did the firmware version download to the switch?

YES

↓

The HAFM server (or customer-supplied server) appears operational. Exit
MAP.

A CTP failure is suspected. Go to

MAP 0000: Start MAP on page 2-6

to isolate the

problem. Exit MAP.

Did the Product Manager application display a window with the message

The data

collection process failed

YES

↓

Go to

step 13

Summary of Contents for 316095-B21 - StorageWorks Edge Switch 2/24



































































































































































































































































































































Search results

Summary of Contents for 316095-B21 - StorageWorks Edge Switch 2/24

Reviews:

Brands by name

Popular brands

HP 316095-B21 - StorageWorks Edge Switch 2/24, Service Manual

Search results

Summary of Contents for 316095-B21 - StorageWorks Edge Switch 2/24

Reviews:

Brands by name

Popular brands