manualshive.com logo in svg

HP 316095-B21 - StorageWorks Edge Switch 2/24, Service Manual

Share
Download
HP 316095-B21 - StorageWorks Edge Switch 2/24 Service Manual Download Page 174

A–4

edge switch 2/24 service manual

Messages

Cannot display route. 
Device is not a 
member of a zone in 
the active zone set.

The user cannot 
show the route for a 
device that is not a 
member of a zone in 
the active zone set. 

Enable the default zone or 
activate the zone for the 
device before attempting to 
show the route.

Cannot display route. 
Error 9.

An internal error 
occurred while trying 
to show routes.

Retry the operation. If the 
condition persists, contact 
support personnel and report 
the problem.

Cannot display route. 
No active zone 
enabled.

You cannot show the 
route through a fabric 
with no active zone.

Enable the default zone or 
activate a zone set before 
attempting to show the route.

Cannot display route. 
All switches in route 
must be managed by 
the same server.

You cannot show the 
route through a fabric 
that has switches or 
directors that are 
managed by a 
different HAFM 
server.

This route cannot be shown 
unless all Edge Switches and 
Directors in the route are 
managed by this HAFM 
server.

Cannot display route. 
All switches in route 
must support routing.

You cannot show the 
route through a fabric 
that has switches or 
directors which do 
not support routing.

The route must contain only 
Directors or Edge Switches

Cannot have spaces 
in field.

Spaces are not 
allowed as part of the 
entry for this field.

Delete spaces from the field 
entry.

Cannot modify a 
zone set with an 
invalid name. 
Rename zone set 
and try again.

A zone set must have 
a valid name to be 
modified.

Assign a valid name to the 
zone set, then click Modify.

Cannot modify a 
zone with an invalid 
name. Rename zone 
and try again.

A zone must have a 
valid name to be 
modified.

Assign a valid name to the 
zone, then click Modify.

Message Description

Action

Summary of Contents for 316095-B21 - StorageWorks Edge Switch 2/24



































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands