manualshive.com logo in svg

HP 316095-B21 - StorageWorks Edge Switch 2/24, Service Manual

Share
Download
HP 316095-B21 - StorageWorks Edge Switch 2/24 Service Manual Download Page 28

2–8

edge switch 2/24 service manual

Diagnostics

6

Reboot the HAFM server (or customer-supplied server) PC. If the customer-supplied 
server does not use the Windows 2000 operating system, refer to the supporting 
documentation to reboot the server.

Reboot the HAFM server PC and perform system diagnostics.

a. Click the Windows Start button. The Windows Workstation menu displays.

b. At the Windows Workstation menu, select Shut Down. The Shut Down 

Windows dialog box appears.

c. At the Shut Down Windows dialog box, select Shut down the Computer and 

click Yes to power off the PC.

d. Wait approximately 30 seconds and power on the PC. After POSTs complete, the 

Begin Logon dialog box displays.

e. At the HAFM Login dialog box, type a user name, password, and HAFM server 

name (obtained in 

step 1

, and all are case sensitive), and click Login. The 

application opens and the Products View displays (

Figure 2–1

).

Figure 2–1:  Products View

Summary of Contents for 316095-B21 - StorageWorks Edge Switch 2/24



































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands