manualshive.com logo in svg

HP 316095-B21 - StorageWorks Edge Switch 2/24, Service Manual

Share
Download
HP 316095-B21 - StorageWorks Edge Switch 2/24 Service Manual Download Page 25

edge switch 2/24 service manual

2–5

Diagnostics

582

Bit error threshold exceeded.

Go to 

MAP 0600

.

583

Loss of signal or loss of synchronization.

Go to 

MAP 0600

.

584

Not operational primitive sequence 
received.

Go to 

MAP 0600

.

585

Primitive sequence timeout.

Go to 

MAP 0600

.

586

Invalid primitive sequence received for 
current link state.

Go to 

MAP 0600

.

810

High temperature warning (CTP thermal 
sensor).

Go to 

MAP 0500

.

811

Critically hot temperature warning (CTP 
thermal sensor).

Go to 

MAP 0500

.

Table 2–3:  Event Codes versus Maintenance Action  (Continued)

Event 

Code

Explanation

Action

Summary of Contents for 316095-B21 - StorageWorks Edge Switch 2/24



































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands