Home
/
HP
/
316095-B21 - StorageWorks Edge Switch 2/24
/
Service Manual

HP 316095-B21 - StorageWorks Edge Switch 2/24, Service Manual

Share

Page: 226 / 322

HP 316095-B21 - StorageWorks Edge Switch 2/24 Service Manual Download Page 226

B–12

edge switch 2/24 service manual

Event Codes

Event Code: 071 (continued)

Event Data
(continued):

4 = Build fabric protocol error. A protocol error was detected during incorporation of
the switch into the fabric. Disconnect the E_Port link, reconnect the link, and IPL the
switch. If the condition persists, perform the data collection procedure and return the Zip
disk to Hewlett-Packard support personnel.

5 = No principal switch. No Director or Edge Switch in the fabric can become the
principal switch. Modify the switch priority to any value other than 255.

6 = No response from attached switch (hello timeout). The switch periodically
verifies operation of attached fabric elements (Director or Edge Switch). The switch
E_Port (at the operational switch) times out and segments if the attached device does
not respond. Check the status of the attached Director or Edge Switch. If the condition
persists, perform the data collection procedure (at the attached device) and return the
Zip disk to Hewlett-Packard support personnel.

7 = ELP retransmission failure timeout. A switch that exhibits a hardware or link
failure attempted to join a fabric and transmitted multiple ELP frames to a fabric element
(Director or Edge Switch). However, because of the problem, the switch did not receive
responses to the ELP frames, and did not receive an FLOGI frame. After five ELP
transmission attempts, the switch E_Port (failed switch) times out and segments. Refer
to

MAP 0000: Start MAP

to perform hardware fault isolation at the failed switch.

Distribution:

Switch

HAFM Server

Host

EWS
Event
Log

System
Error
LED

Event
Log

E-Mail

Call
Home

Sense
Info

Link
Incident

✔

✔

Event Code: 072

Message:

E_Port connected to unsupported switch.

Severity:

Informational.

Explanation:

The switch is attached (through an ISL) to an incompatible fabric element (Director or
Edge Switch).

Action:

Disconnect the ISL.

Event Data:

No supplementary data included with this event.

Distribution:

Switch

HAFM Server

Host

EWS
Event
Log

System
Error
LED

Event
Log

E-Mail

Call
Home

Sense
Info

Link
Incident

✔

✔

«
...
224
225
226
227
228
...
»

Summary of Contents for 316095-B21 - StorageWorks Edge Switch 2/24



































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands