HP 316095-B21 - StorageWorks Edge Switch 2/24 Service Manual Download Page 50

Page: 50 / 322

2–30

edge switch 2/24 service manual

Diagnostics

Is a failure indicated?

YES

↓

The switch appears operational. Exit MAP.

Contact the next level of support. Exit MAP.

Is fault isolation being performed at the switch?

YES

↓

Fault isolation is being performed at the HAFM server (or customer-supplied
server) or EWS interface. Go to

step 19

Verify the switch is connected to facility power and is powered on.

a. Ensure AC power cords (PS0 and PS1) are connected to the rear of the switch

and to facility power receptacles. If not, connect the cords as directed by the
customer.

b. Ensure associated facility circuit breakers are on. If not, ask the customer set the

circuit breakers on.

c. Ensure the AC power cords are not damaged. If damaged, replace the cords.

Continue.

Inspect the switch for indications of being powered on, such as:

•

At the front bezel, an illuminated power LED (green) or system error LED
(amber).

•

Audio emanations and airflow from cooling fans.

Does the switch appear powered on?

YES

↓

Go to

step 14

Summary of Contents for 316095-B21 - StorageWorks Edge Switch 2/24



































































































































































































































































































































Search results

Summary of Contents for 316095-B21 - StorageWorks Edge Switch 2/24

Reviews:

Brands by name

Popular brands

HP 316095-B21 - StorageWorks Edge Switch 2/24, Service Manual

Search results

Summary of Contents for 316095-B21 - StorageWorks Edge Switch 2/24

Reviews:

Brands by name

Popular brands