manualshive.com logo in svg

HP 316095-B21 - StorageWorks Edge Switch 2/24, Service Manual

Share
Download
HP 316095-B21 - StorageWorks Edge Switch 2/24 Service Manual Download Page 34

2–14

edge switch 2/24 service manual

Diagnostics

20

A link incident may have occurred, but the LIN alerts option is not enabled for the port 
and the attention indicator does not appear. 

At the Hardware View, click Logs and select Link Incident Log. The Link Incident 
Log displays (

Figure 2–3

).

Figure 2–3:  Link Incident Log

If a link incident occurred, the affected port number is listed with one of the following 
messages.

Link interface incident - implicit incident.

Link interface incident - bit-error threshold exceeded.

Link failure - loss of signal or loss of synchronization.

Link failure - not-operational primitive sequence (NOS) 

received.

Summary of Contents for 316095-B21 - StorageWorks Edge Switch 2/24



































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands