manualshive.com logo in svg

HP 316095-B21 - StorageWorks Edge Switch 2/24, Service Manual

Share
Download
HP 316095-B21 - StorageWorks Edge Switch 2/24 Service Manual Download Page 182

A–12

edge switch 2/24 service manual

Messages

Invalid request.

Three conditions 
result in this 
message:

•

The user tried to 
add or modify a 
product from 
product view and 
the network (IP) 
address is already 
in use. Network 
addresses must 
be unique.

•

The user tried to 
create a new user 
with a user name 
that already 
exists. User 
names must be 
unique.

•

The user tried to 
delete default 
Administrator 
user. The default 
Administrator user 
cannot be 
deleted.

Select the action that is 
appropriate to the activity that 
caused the error:

•

Network address: Specify 
a unique network (IP) 
address for the product.

•

User name: Specify a 
unique user name for the 
new user ID.

•

Do not delete the default 
Administrator user.

Invalid HAFM server 
address.

The IP address 
specified for the 
HAFM server is 
unknown to the 
domain name server 
(invalid).

Verify and enter a valid HAFM 
server IP address.

Message Description

Action

Summary of Contents for 316095-B21 - StorageWorks Edge Switch 2/24



































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands