manualshive.com logo in svg

HP 316095-B21 - StorageWorks Edge Switch 2/24, Service Manual

Share
Download
HP 316095-B21 - StorageWorks Edge Switch 2/24 Service Manual Download Page 252

B–38

edge switch 2/24 service manual

Event Codes

Event Code: 510

Message:

SFP optical transceiver hot-insertion initiated.

Severity:

Informational.

Explanation:

Installation of a small form factor pluggable (SFP) optical transceiver was initiated with 
the switch powered on and operational. The event indicates that operational firmware 
detected the presence of the transceiver.

Action:

No action required.

Event Data:

Byte 0 = port number (00 through 23).

Bytes 4 through 7 = elapsed millisecond tick count.

Distribution:

Switch

HAFM Server

Host

EWS 
Event 
Log

System 
Error 
LED

Event 
Log

E-Mail

Call 
Home

Sense 
Info

Link 
Incident

✔

✔

Event Code: 512

Message:

SFP optical transceiver nonfatal error.

Severity:

Minor.

Explanation:

Switch firmware detected an SFP optical transceiver non-fatal error.

Action:

Replace the failed transceiver with a functional transceiver of the same type.

Event Data:

Byte 0 = port number (00 through 23).

Byte 1 = engineering reason code.

Bytes 4 through 7 = elapsed millisecond tick count.

Distribution:

Switch

HAFM Server

Host

EWS 
Event 
Log

System 
Error 
LED

Event 
Log

E-Mail

Call 
Home

Sense 
Info

Link 
Incident

✔

✔

Summary of Contents for 316095-B21 - StorageWorks Edge Switch 2/24



































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands