manualshive.com logo in svg

Hitachi ZW 550-6, Operator'S Manual

The Hitachi ZW 550-6 is a robust and efficient construction machine designed for heavy-duty work. To harness its full potential, it is imperative to utilize the Operator's Manual. Get the comprehensive manual for this product, available for free download at manualshive.com, and optimize your productivity and performance on the field.

Share
Download
background image

OPERATOR'S STATION

1-30

Display

Contents of Alarms

Remedy

Hydraulic Oil Overheat Alarm

Hydraulic oil temperature is above normal. Stop operation. Run the 

engine at slow idle speed to lower the oil temperature.

Axle Oil Temperature Alarm

Axle oil temperature is above normal. Check if the service brake drags.

Transmission Oil Temperature 

Alarm

Transmission oil temperature is above normal. Stop operation. Run 

the engine at slow idle speed to lower the oil temperature. 

Use correct range for machine operation, and do not stall torque 

converter. 

Engine Trouble Alarm

Engine or engine related parts are abnormal. Immediately set the 

machine in the park position, apply parking brake, stop the engine 

and contact your authorized dealer. 

Transmission Alarm

Transmission or transmission related parts are abnormal. Immediately 

set the machine in the park position, apply parking brake, stop the 

engine and contact your authorized dealer. 

Engine Oil Pressure Alarm

Engine oil pressure has decreased.

Immediately stop the engine, and apply parking brake. Check the 

engine oil system and oil level.

Boost Temperature Rise Alarm

Intake air temperature is abnormally high. Stop operation. Check 

intercooler for clogging and intake air piping connections.

Auto Brake Warning Alarm

Auto brake system is abnormal. 

Safely park the machine and stop the engine immediately. Check 

hydraulic oil level and auto brake system for damages and leaks. 

Transmission Filter Clogging

Transmission filter elements are clogged. 

Replace transmission oil filter following the instruction in the 

operator's manual.

Transmission Oil Pressure 

Alarm

Transmission oil pressure is too low. Safely park the machine. Check 

transmission oil level and check for leaks. 

Main Pump Oil Pressure Alarm

Main pump oil pressure has decreased. Stop machine operation, and 

apply parking brake. Check the piping of front attachment for oil 

leaks. 

Summary of Contents for ZW 550-6























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ZW 550-6

Honda FL6555 Operator'S Manual preview
FL6555
Brand: Honda Pages: 66

Brands by name

Popular brands

Load more brands