manualshive.com logo in svg

Hitachi ZW 550-6, Operator'S Manual, Page: 417 / 438

Share
Download
Hitachi ZW 550-6 Operator'S Manual Download Page 417

9-3

MAINTENANCE UNDER SPECIAL ENVIRONMENTAL CONDITIONS

d

DANGER:  Ventilate the area with fresh air when 

carrying out warm-up operation indoor. Failure to do 

so may cause asphyxiation from exhaust gas, resulting 

in death or severe injury.

7.  After preheating, start and warm up the engine.
8.  After warming up the engine, warm up the loading 

hydraulics. Slowly operate the control levers to move 

the cylinders full stroke several times. Do not force 

cylinders to go to the end of their stroke.

9.  Road surfaces covered with snow, especially when snow 

has been compacted, will be frozen. Use tire chains on 

all four wheels.

10.  Take anti-freeze measures after completing operation.

  Spray keyholes with light oil. Cover the keyhole by 

sticking a tape on.

  Rubber parts such as wiper blades may freeze. Keep 

other parts away from the rubber parts. Warm up cab 

prior to use of wipers.

  Remove packed snow from around the axles, articulation 

joint and inside the machine with a bar or brush. Be 

careful not to damage electrical wiring.

  In case it is impossible to store the machine indoors, 

park the machine on a level dry surface and cover the 

machine with a large machine cover.

  Keep 80% of tank capacity when storing DEF. The DEF 

tank maybe broken if frozen.

f

NOTE:  DEF may start freezing at -10°C (12°F). Freezing does 

not affect its performance once thawed. 

Summary of Contents for ZW 550-6























































































































































































































































































































































































































































Reviews:

No comments