Hitachi ZW 550-6 Operator'S Manual Download

Page: 92 / 438

OPERATOR'S STATION

1-28

Follow the procedure below to display detailed information for

an alarm.

Push selector knob (1) on the basic screen to display the

main menu.

Rotate selector knob (1) to select the alarm list, and push

selector knob (1).

NOTE: The main menu displays the alarm list (faults) only

when an alarm occurs.

Rotate selector knob (1) to select a required alarm from the

alarm list, and push selector knob (1).

NOTE: The alarm list contains only active faults or alarms.

Detailed information of the selected alarm will be displayed.

MNEC-01-006

MNHG-01-290EN

MNHG-01-105EN

MNHG-01-106EN

MNHG-01-107EN

Summary of Contents for ZW 550-6























































































































































































































































































































































































































































Search results

Summary of Contents for ZW 550-6

Reviews:

Related manuals for ZW 550-6

Brands by name

Popular brands

Hitachi ZW 550-6, Operator'S Manual

Search results

Summary of Contents for ZW 550-6

Reviews:

Related manuals for ZW 550-6

Brands by name

Popular brands