Hitachi ZW 550-6 Operator'S Manual Download Page 230

Page: 230 / 438

MOVING THE MACHINE

4-4

4. Manual Shift (M)
After setting forward/reverse switch (11) to either

forward (F) or reverse (R) position, press the shift

switch (12) to the desired position. The transmission

gear position can be shifted in 4 ranges in the

forward and 3 ranges in the reverse mode. Select

the most appropriate transmission range position

according to the operating conditions.

Manual Mode:

Manual shift mode.

The transmission gear is shifted by pressing

shift up/down switches (12).

5. Auto Shift
Set forward/reverse switch (11) to (F) or (R). Select

the most appropriate transmission range position

according to the operating conditions. Select the

most appropriate travel pattern by operating travel

mode selector (13).

AUTO 1 Mode:

This mode sets 1st range as the minimum

speed gear stage.

Start traveling with 2nd range. When driving

load increases, it automatically shifts to 1st

range.

This mode is suited for heavy digging work or

ascending on a slope.

AUTO 2 Mode:

This mode sets 2nd range as the minimum

speed gear stage.

This mode is suited for removing snow or

lighter applications.

NOTE:



Avoid operating this switch while machine is moving.



Do not use this switch on a slope. Use of the Quick

Power Switch is recommended to have more

acceleration while ascending on a slope.

(Refer to page 1-111 for Quick Power Switch.)

7. Release brake pedals (7) and step on accelerator

pedal (10) to start traveling.

115Z7B-4-4-1

Shift up

Shift down

MNEC-01-024

AUTO 1 Mode

Manual Mode

AUTO 2 Mode

Summary of Contents for ZW 550-6























































































































































































































































































































































































































































Search results

Summary of Contents for ZW 550-6

Reviews:

Related manuals for ZW 550-6

Brands by name

Popular brands

Hitachi ZW 550-6, Operator'S Manual

Search results

Summary of Contents for ZW 550-6

Reviews:

Related manuals for ZW 550-6

Brands by name

Popular brands