Hitachi ZW 550-6 Operator'S Manual Download Page 386

Page: 386 / 438

MAINTENANCE

7-102

Check Air Conditioner Condenser
--- every 6 months

If condenser (1) is covered with dirt and/or insects, air

conditioner cooling performance will be reduced. Remove

dirt or stain foreign material from fins of condenser (1)

using tap water. In case the condenser has been severely

contaminated, use a soft brush or a plastic fin comb tool.

Do not use a hard brush, which may damage the fins.

Check Air Conditioner Compressor Belt
--- every 6 months

Check the belt for abnormal deflection and damage. Check

HVAC belt tension by using tension gauge.

Belt tension: 412±49 N (42±5 kgf, 93±11 Ibf)

NOTE: The belt tension should be 588±98 N (60±10 kgf,

132±22 lbf) when the belt is replaced with new one.

Compressor Belt Tension Adjustment Procedure

1. Loosen lock nuts (2, 6) of tension pulley (4).
2. Remove plate (5) and tension pulley (4) to adjust belt

tension by turning belt tension adjustment bolt (3).

3. After adjustment, securely tighten lock nuts (2, 6) and

mount plate (5).

Nut (2): 52.5 N·m (5.35 kgf·m, 38.7 lbf·ft)

115Z7B-7-102-1

95Z7-7-92-2

Summary of Contents for ZW 550-6























































































































































































































































































































































































































































Search results

Summary of Contents for ZW 550-6

Reviews:

Related manuals for ZW 550-6

Brands by name

Popular brands

Hitachi ZW 550-6, Operator'S Manual

Search results

Summary of Contents for ZW 550-6

Reviews:

Related manuals for ZW 550-6

Brands by name

Popular brands