Hitachi ZW 550-6 Operator'S Manual Download Page 320

Page: 320 / 438

MAINTENANCE

7-36

Check Planetary Gear Oil Level

NOTE: Check the oil level on all four wheels.

6. Clean the vicinity of oil level plug (4).

7. Check that "TOP" mark (3) on the planetary gear

housing comes top as shown. If not, move the

machine and adjust the position.

8. Make sure to turn ON the parking brake switch, lower

the attachment to the ground, and stop the engine.

9. Remove oil level plug (4) on the housing.

10. If the oil level is lower than the plug, add the

specified oil through the level plug hole.

11. Magnetic plugs are used for the planetary gear

housing. Wipe off the small amount of fine metallic

powder that normally sticks to the plugs. If abnormal

debris is found, determine the cause and correct it.

12. If there is any sign of water in the oil, drain and

replace the oil. Oil containing water looks milky.

Dispose of the drained oil properly.

13. Install and tighten the level plug.

115Z7-7-40-2

Summary of Contents for ZW 550-6























































































































































































































































































































































































































































Search results

Summary of Contents for ZW 550-6

Reviews:

Related manuals for ZW 550-6

Brands by name

Popular brands

Hitachi ZW 550-6, Operator'S Manual

Search results

Summary of Contents for ZW 550-6

Reviews:

Related manuals for ZW 550-6

Brands by name

Popular brands