Hitachi ZW 550-6 Operator'S Manual Download

Page: 427 / 438

11-5

TROUBLESHOOTING

6. Drive Function (Continued)

Problem

Cause

Solution

Transmission is noisy.

Lack or deterioration of gear oil

Refill, replace

Worn inner parts in transmission

* Repair, Replace

Broken gear or bearing

* Repair, Replace

Oil temperature increases.

Faulty fan rotation

* Repair or adjust

Propeller shaft vibrates.

Bent propeller shaft

* Repair, Replace

Loosened parts, Loss of balance

* Retighten, Adjust

Propeller shaft is noisy

Excessively worn spline

* Replace

Worn or seized spider bearing

* Replace

Loosened parts

* Retighten

Insufficient greasing

Grease

Front and/or rear axle is noisy

Worn or broken gears

* Replace

Lack or deterioration of gear oil

Refill, Replace

Worn bearings, Excess play

* Replace

Excess play on shaft spline

* Repair, Replace

Front and/or rear axle does not

transmit power.

Broken axle

* Repair

Broken gears

* Repair

NOTE: * Consult the nearest authorized dealer.

7. Others

The machine may have a noise, excessive vibration, and

abnormal smell when any trouble occurs. Always beware of

the machine conditions during operation.

Summary of Contents for ZW 550-6























































































































































































































































































































































































































































Search results

Summary of Contents for ZW 550-6

Reviews:

Related manuals for ZW 550-6

Brands by name

Popular brands

Hitachi ZW 550-6, Operator'S Manual

Search results

Summary of Contents for ZW 550-6

Reviews:

Related manuals for ZW 550-6

Brands by name

Popular brands