manualshive.com logo in svg

Hitachi ZW 550-6, Operator'S Manual

The Hitachi ZW 550-6 is a robust and efficient construction machine designed for heavy-duty work. To harness its full potential, it is imperative to utilize the Operator's Manual. Get the comprehensive manual for this product, available for free download at manualshive.com, and optimize your productivity and performance on the field.

Share
Download
background image

MAINTENANCE

7-101

Check Air Conditioner
--- every 6 months

Check the air conditioner switch panel, air conditioner unit, 

and condenser mounting areas for any troubles, and check 

hoses for any damage.

f

NOTE:  When the season to use the air conditioner comes 

close, check the air conditioner to get it ready to use at 

all times. When not required to use the air conditioner for 

a long period of time, operate the air conditioner in the 

cooling mode once a week to prevent lack of lubrication.

d

CAUTION:  Avoid steam cleaning

 

Do not clean the compressor and receiver tank 

with steam. The high temperature will cause the 

refrigerant gas pressure to increase, possibly 

causing the hoses to break. This could injure 

personnel.

Check Air Conditioner Piping
--- every 6 months

d

IMPORTANT:  If any leakage is found, repair or 

replace the corresponding pipes. Tighten the joint 

bolts to specification.

Check the piping for deformation and/or damage. If a pipe 

joint is contaminated with oil, refrigerant leakage may be 

suspected. Check for leakage using a refrigerant gas leak 

detector. 

Summary of Contents for ZW 550-6























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ZW 550-6

Brands by name

Popular brands

Load more brands