Hitachi ZW 550-6 Operator'S Manual Download Page 89

Page: 89 / 438

OPERATOR'S STATION

1-25



Fan Reverse Rotation Indicator (16)

Displays rotating direction of the fan.

Normal Rotation



The icon is not displayed.

Changing Rotational

Direction



The icon blinks.

Reverse Rotation



The icon lights ON.



HOLD Display (17)

Hold display (17) is displayed when the hold switch on

the side console is in ON position.



Transmission Auto-shifting Indicator (18)

Transmission auto-shifting indicator (18) displays

condition of the travel mode switch. It is not displayed at

manual mode.



F-N-R/Shift Position Indicator (19)

F-N-R/Shift Position Indicator (19) displays machine

operating condition (status of the transmission).

F-N-R Display

F-N-R indicator displays status of the transmission.

Forward



Neutral



Reverse



Shift Position Indicator

It displays currently engaged gears. It is not displayed at

neutral position.

Forward

: 1st - 4th

Reverse

: 1st - 3rd



Auto Brake Indicator (20)

Auto brake indicator (20) appears when the auto brake

works due to excessive machine speed or when direction

is changed while running at the specified speed or faster.

It automatically turns off when the machine speed

decreases below within the safety speed limit.

Refer to Auto Brake in "MOVING THE MACHINE" section.



Joystick Steering Indicator (21)

Joystick steering indicator appears when the joystick

steering is made effective by turning on the armrest

switch. Refer to "OPERATING THE ENGINE".



Traction Control Indicator (22)

Traction control indicator (22) appears when the traction

control is turned ON by the setting menu. Refer to page

1-63.



Torque Converter Lock-Up Indicator (23)

T/C lock-up indicator (23) appears during the lockup

shifting. Refer to page 4-5.

MNHG-01-100EN

Summary of Contents for ZW 550-6























































































































































































































































































































































































































































Search results

Summary of Contents for ZW 550-6

Reviews:

Related manuals for ZW 550-6

Brands by name

Popular brands

Hitachi ZW 550-6, Operator'S Manual

Search results

Summary of Contents for ZW 550-6

Reviews:

Related manuals for ZW 550-6

Brands by name

Popular brands