Hitachi ZW 550-6 Operator'S Manual Download

Page: 179 / 438

OPERATOR'S STATION

1-115

Auto Air Conditioner

Feature



Full Auto-Temperature Control:

Automatically controls the cab temperature to maintain

the temperature set by the temperature control switch

regardless of outside air temperature and insolation.



Max. Cooling and Heating:

Maximum cooling or heating can be obtained by

rotating the temperature control switch clockwise (32°C)

(90°F) or counterclockwise (18°C) (64°F) respectively.



Preheating:

During preheating the cab in winter with the foot

vent selected, the air volume is reduced to Low until

the coolant temperature rises to prevent cool air from

entering the cab.

NOTE: Even in the summer season, the engine high

idle speed may be higher when cool than the normal

operating temperature speed due to quick warm-up

mode.

Summary of Contents for ZW 550-6























































































































































































































































































































































































































































Search results

Summary of Contents for ZW 550-6

Reviews:

Related manuals for ZW 550-6

Brands by name

Popular brands

Hitachi ZW 550-6, Operator'S Manual

Search results

Summary of Contents for ZW 550-6

Reviews:

Related manuals for ZW 550-6

Brands by name

Popular brands