manualshive.com logo in svg

Hitachi ZW 550-6, Operator'S Manual

The Hitachi ZW 550-6 is a robust and efficient construction machine designed for heavy-duty work. To harness its full potential, it is imperative to utilize the Operator's Manual. Get the comprehensive manual for this product, available for free download at manualshive.com, and optimize your productivity and performance on the field.

Share
Download
background image

MAINTENANCE

7-62

Replace Fuel Main Filter Element
--- every 500 hours or when fuel filter restriction 

indicator is lit

d

CAUTION:  Depending on the circumstance, diesel 

fuel is flammable. When inspecting or performing 

service or repairs on the fuel system, to reduce the 

possibility of fire and resulting severe personal 

injury, death, or property damage, never smoke 

or allow sparks or flames (such as pilot lights, 

electrical switches, or welding equipment) in the 

work area. 

IMPORTANT:

 

Be sure to use only genuine Hitachi elements for 

the fuel main filter element and the pre-filter 

element. Failure to do so may lower engine 

performance and/or shorten the engine service 

life. 

 

Make sure that debris, water, steam, or cleaning 

solution does not get inside the fuel system.

1.  Prepare 1 liter (1 quart) or larger capacity container to 

hold the drained fuel. 

2.  Loosen and remove fuel main filter (1) using the 

provided filter wrench. 

f

NOTE:  Make sure the filter gasket (2) does not stick to the 

filter head.

3.  Apply a light film of clean engine oil to gasket surface 

of the new filter.

IMPORTANT:  Do not fill fuel main filter (1) with fuel 

before installation. 

4.  Install empty fuel main filter (1) to the filter head. 

d

CAUTION:  Mechanical overtightening can distort 

the threads as well as damage the filter element 

seal or filter canister. 

5.  Tighten the filters an additional two-thirds turn after 

the gasket contacts the filter head surface. Follow the 

instructions supplied with the filter. 

f

NOTE:  Main filter (1) tightening torque: 25 N·m (2.5 

kgf·m, 18.5 lbf·ft) 

95Z7B-7-64-2

1

2

3

115Z7B-7-58-1

Main Filter

Summary of Contents for ZW 550-6























































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ZW 550-6

DRESSTA 515C Operator'S Manual preview
515C
Brand: DRESSTA Pages: 205
Kubota LA1153 Workshop Manual preview
LA1153
Brand: Kubota Pages: 122
Hyundai HB100 Manual preview
HB100
Brand: Hyundai Pages: 21
Bush Hog Front-Push Loader 2847QT Specifications preview
Front-Push Loader 2847QT
Brand: Bush Hog Pages: 1
Bush Hog M146 Operator'S Manual preview
M146
Brand: Bush Hog Pages: 39
Bush Hog 1747 Parts Manual preview
1747
Brand: Bush Hog Pages: 30
Bush Hog 3860 QT Operator'S Manual preview
3860 QT
Brand: Bush Hog Pages: 46
Avant Tecno Oy Avant 850 Operator'S Manual preview
Avant 850
Brand: Avant Tecno Oy Pages: 138

Brands by name

Popular brands

Load more brands